Beam Air : The Universal Laser Cutter Fume Extractor Beam Air : The Universal Laser Cutter Fume Extractor

$ 849.00 $ 799.00

-
+
$ 799.00
Add to wishlist

Beam Air Fume Extractor

Beam Air

The Beam Air is a universal fume extractor for laser cutters. Whether planning to buy a laser cutter for home, hobby, or business use, the Beam Air can provide the ability to minimize or eliminate a majority of particles and scents of materials in use for almost any laser cutter.

If already using a laser cutter, the strong scents and particles that could be emitted from the laser cut material may be all too familiar. The Beam Air can efficiently solve these problems by using four layers of technologically advanced filters:

Flux Beam Air Fume Extractor

Pre-Filter

Medium Efficiency Filter

H13 HEPA Filter

Activated Charcoal Filter

This is the first layer of defense! The pre-filter is positioned on the top of the Beam Air, so it is the first filter that will be preventing particles from passing through – coming from the laser cutter which is connected via a tube. Because this filter is the thinnest and the top layer, this filter will need to be replaced after every 10 – 30 hours of use.

Just below the pre-filter, the medium efficiency filter provides a buffer and further filtering out particles which managed to get through the pre-filter. To ensure the Beam Air is eliminating as many particles from passing to the outside environment, this filter will need to be replaced after every 50 – 150 hours of use.

The third section of the Beam Air is known as the H13 HEPA Filter and as it is near the center of the Beam Air, it filters out the few remaining particles that may have penetrated past the other two filters. This filter will need to be replaced after every 100 – 200 hours of use.

This is the bottom filter, or final filter, of the Beam Air. Particles have to make it past three other filters to reach this one. This filter can eliminate almost all of the particles at this point, allowing for the Beam Air to be a proficient fume extractor. This long-lasting filter will need to be replaced after every 300 – 600 hours of use.


Compatible with:

- beamo
- Beambox 40W
- Beambox Pro 50W
- Glowforge Pro
- Glowforge Plus
- Glowforge Basic
- Dremel DigiLab LC40
- Emblaser 2
- Makeblock
- K40 Laser Cutter

...And many more! Showcasing the universality of the Beam Air even more, almost any laser cutter’s hose can be connected to the Beam Air so that it can extract the particles from the air in the laser cutter, though it may require a simple tube reducer or expander to connect the sizing difference.

Overall, the Beam Air is an ideal solution for many laser cutter users due to its ease of use, beneficial fume extracting ability, and its compatibility with so many laser cutters.

Technical Specifications:

System Flow: 353 CFM - 195 CFM
Air Felt Interface: Φ 100mm
Product Size: 37 x 26 x 45 cm (14.57 x 10.24 x 17.72 in)
Package Size: 49 x 37 x 50 cm (19.29 x 14.57 x 19.69 in)
Weight: 17 kg (37.5 lb)
Voltage: AC110V & AC220V
Power: 130W

Beam Air Fume Extractor

Beam Air

The Beam Air is a universal fume extractor for laser cutters. Whether planning to buy a laser cutter for home, hobby, or business use, the Beam Air can provide the ability to minimize or eliminate a majority of particles and scents of materials in use for almost any laser cutter.

If already using a laser cutter, the strong scents and particles that could be emitted from the laser cut material may be all too familiar. The Beam Air can efficiently solve these problems by using four layers of technologically advanced filters:

Flux Beam Air Fume Extractor

Pre-Filter

Medium Efficiency Filter

H13 HEPA Filter

Activated Charcoal Filter

This is the first layer of defense! The pre-filter is positioned on the top of the Beam Air, so it is the first filter that will be preventing particles from passing through – coming from the laser cutter which is connected via a tube. Because this filter is the thinnest and the top layer, this filter will need to be replaced after every 10 – 30 hours of use.

Just below the pre-filter, the medium efficiency filter provides a buffer and further filtering out particles which managed to get through the pre-filter. To ensure the Beam Air is eliminating as many particles from passing to the outside environment, this filter will need to be replaced after every 50 – 150 hours of use.

The third section of the Beam Air is known as the H13 HEPA Filter and as it is near the center of the Beam Air, it filters out the few remaining particles that may have penetrated past the other two filters. This filter will need to be replaced after every 100 – 200 hours of use.

This is the bottom filter, or final filter, of the Beam Air. Particles have to make it past three other filters to reach this one. This filter can eliminate almost all of the particles at this point, allowing for the Beam Air to be a proficient fume extractor. This long-lasting filter will need to be replaced after every 300 – 600 hours of use.


Compatible with:

- beamo
- Beambox 40W
- Beambox Pro 50W
- Glowforge Pro
- Glowforge Plus
- Glowforge Basic
- Dremel DigiLab LC40
- Emblaser 2
- Makeblock
- K40 Laser Cutter

...And many more! Showcasing the universality of the Beam Air even more, almost any laser cutter’s hose can be connected to the Beam Air so that it can extract the particles from the air in the laser cutter, though it may require a simple tube reducer or expander to connect the sizing difference.

Overall, the Beam Air is an ideal solution for many laser cutter users due to its ease of use, beneficial fume extracting ability, and its compatibility with so many laser cutters.

Technical Specifications:

System Flow: 353 CFM - 195 CFM
Air Felt Interface: Φ 100mm
Product Size: 37 x 26 x 45 cm (14.57 x 10.24 x 17.72 in)
Package Size: 49 x 37 x 50 cm (19.29 x 14.57 x 19.69 in)
Weight: 17 kg (37.5 lb)
Voltage: AC110V & AC220V
Power: 130W

Recently Viewed Products Recently Viewed Products

Liquid error: Could not find asset snippets/zopim.liquid